Type: Driver
File Name:
File Size: 37.2 MB
21 (4.79)
Downloads: 17
Supported systems: Windows 7/8/10, Windows XP 64-bit, Mac OS X 10.X
Price: Free* (*Free Registration Required)

Download Now

Report any shipping bizhub c451 fiery. Never alter an existing network without permission. Never assign an IP address in Network Setup. Precautions 4. Avoid flexing a printed circuit board, and handle it by opposing edges not corners only.

Konica Minolta bizhub C451 User Manual

Never set a cup of coffeeor any liquidon or near any components or the copier. Exploded View Exploded View 1 2a 3 2b Key 15 1. Interface board 4. DIMM 10 5. bizhub c451 fiery


Battery 11 6. Fiery X3eTY2 motherboard 12 7. Fiery X3eTY2 power supply 8. Enclosed fan 16 9. Connector panel see page bizhub c451 fiery 13 17 Extender card Rail Power off the copier using the main power switch inside the copier. Wait while the Fiery X3eTY2 shuts down. Shut down the Fiery X3eTY2 and the copier see page 8. Disconnect all external cables from the connector panel of the Fiery X3eTY2. Remove the four screws that attach the Fiery X3eTY2 to the copier. Unhook and remove the Fiery X3eTY2 from the copier. You must shift the Fiery X3eTY2 to the left to release it from the copier. AC power switch upper two leads : 6. Specifically check all other power supply cable connections in the pan: Location Component or cable AC power switch, 4 lead, 2x2 Power supply with attached cable, split to two wires: White wire to the upper lead corresponding to ON; Black wire to the upper lead corresponding to OFF HDD Power supply with attached SATA power cable After you verify connections, if one or more Fiery X3eTY2 components is still not receiving power, check the copier and its internal interface to the Fiery X3eTY2 for information, bizhub c451 fiery the documentation that accompanies the copier.

Access and open the Fiery X3eTY2, as described on page 9. Disconnect the interface board from Slot 2 top slot of the extender card. Insert the interface board into the extender card Slot 2 top slot. Bizhub c451 fiery the cover plate to the connector panel with the two screws you removed earlier.

Locate the battery on the Fiery X3eTY2. Carefully bend the clip that bizhub c451 fiery the battery. Use caution when bending the clip; excessive force could cause the clip to lose its tension. Battery Socket Clip 3.

Pull the battery out of its socket and release the clip. Make sure the clip holds the battery securely in the socket. Filtered by:. Share your experiences with others.

Konica Minolta bizhub C : User guide

Results 1 to 4 of 4. Gonna be in the UK in about a month.


BarnabusJul 13, Interface board The interface board connects directly to the extender card, which is connected directly to the Fiery X3eTY2 motherboard see Figure H, below, and Figure B on page 5. Remove the bizhub c451 fiery cover plate screws that connect the interface board to the connector panel see Figure B on page 5. You do not need to remove the jackscrews that connect the cover plate to the interface board. Bend out the pan slightly so that you can slide the interface board out of the connector panel cutout as you lift the board out of the extender card. Lift out the interface board from the pan.Hi, I need some input from anyone who has installed a IC in a Konica C The install went pretty smooth and the Fiery boots up to a. I have a Konica Minolta Bizhub C The Fiery server is X3eTY-E5E0 and it looks like the version is I cannot calibrate the thing anymore.

brother pt-9500pc label printerRelated titles
logitech b100Bizhub c-451 / Fiery Ic-409 Problems

Other Drivers