FIERY 50-45C-KM DRIVER DETAILS:
|File Size:||11.3 MB|
|Supported systems:||Windows 10, Windows 8.1, Windows 7|
|Price:||Free* (*Free Registration Required)|
FIERY 50-45C-KM DRIVER
EFI - Downloads - Support & Downloads
Free Shipping. Add to cart. Insert each screw into a spring, fiery 50-45c-km then insert the screw assembly into the heatsink.
Turn the screw until the screw threads completely protrude through base of heatsink. Place the cooling assembly on the CPU.
Be sure to remove any protective material that may be covering the surface of the thermal pad. Otherwise, the CPU may Screw overheat. Tighten fiery 50-45c-km screws. Partially tighten all Screw post the fiery 50-45c-km before tightening any one 1 of 4 screw all the way. The cable connector is keyed to fit only one way.
Make sure that the connector on the cable is securely attached to connector FAN1 on the motherboard. Install the motherboard in the chassis see page Replace the motherboard components see page Remove the battery see page Wait two minutes to allow the motherboard electrical components to fully discharge. Reinstall the battery see page Jumpers This following table describes the factory default configuration for jumpers on the motherboard. Jumper configurations should not be changed. Because the jumper cap is very small, it is not necessaryand could introduce an errorto remove the jumper cap in order to clear the CMOS settings. fiery 50-45c-km
Instead, to clear CMOS settings, deny power to the motherboard as described below. To clear CMOS settings: 1. Wait one full minute to allow fiery 50-45c-km motherboard electrical components to fully discharge. Close fiery 50-45c-km Fiery E10 page 42reconnect the power cable, and then power on by pressing the power button on the front panel. JP4 No jumper cap is installed.
- Genuine Konica Minolta - Fiery E10 C-KM and 50 similar items
- Genuine Konica Minolta - Fiery E10 C-KM Color Server/Printer Controller -
- Online Services - Search
- Genuine Konica Fiery E10 50-45C-KM Color Server/Printer Controller - FedEx 2 Day
- Genuine Konica Minolta – Fiery E10 50-45C-KM Color Server/Printer Controller
- Related titles
- Dealing with EFI Fiery Drivers for OS X El Capitan
JP5 No jumper cap is installed. JP6 No jumper cap is installed. JP7 No jumper cap is installed. JP8 No jumper cap is installed. Service board The Fiery E10 uses a Service board to offer service mode switches for installing fiery 50-45c-km software over the network and Service LEDs arrayed as a 2-digit display.
Genuine Konica Minolta - Fiery E10 50-45C-KM and 50 similar items
The Service board is attached to the pan with four screws and is attached to the motherboard by a ribbon fiery 50-45c-km. Shut down and open the Fiery E10 see pages 13 fiery 50-45c-km Remove the Service board ribbon cable from the motherboard J26 connector. Do not pull the wires of the cable. Pull the cable out by its connector.
Remove the four screws that secure the Service board to the pan. Fiery 50-45c-km you remove the Service board, carefully slide the ribbon fiery 50-45c-km through the space between the extender card and the pan. Set the screws aside so that you can replace them later.
fiery 50-45c-km Remove the ribbon cable from connector J1 on the Service board. Position the Service board in the chassis and secure the Service board to the chassis with the screws you removed earlier see Figure 2 on page Connect the Service board ribbon cable to the Service board J1 connector and fiery 50-45c-km the motherboard J26 connector see Figure 8 on page Enclosed fan One enclosed fan is attached to the pan to cool the system.INF file name, INF file date, 10/2/ Version. Class, printer. WHQL status.
Fiery E10 50 45c Km Driver
Compatible hardware, Fiery E10 C-KM PCL1. INF file name, INF file fiery 50-45c-km, 10/2/ Version. Class, printer.
WHQL status. Compatible hardware, Fiery E10 C-KM PS1.